These are for 2006 & earlier TSSM 

                                                                                These are for 2007 & Later HFSM

 HFSM-Siren Chirp Enable Feature

There has been some confusion surrounding the enabling and disabling of chirp/chirpless

mode on 2007 models equipped with the optional smart siren.

To enable or disable the chirp mode on the smart siren:

The engine RUN/OFF switch must be left in the RUN position (ON) during this entire process.

The fobs must be present as well.

Turn the ignition key switch to Ignition and leave ON until the security lamp goes out. Once

the lamp goes out, turn the switch OFF. The system will arm itself.

Repeat the above process 2 more times. (Key ON, key OFF, key ON, key OFF), each time

waiting for the light to go off.

After this cycle has been performed a total of 3 times, the Chirp feature will change to

enabled or disabled, depending on the current status.

In the chirpless mode the siren does not chirp upon arming or disarming.

The siren will still chirp warnings on movement and will activate through all alarm cycles.

                                                                   HFSM- PERSONAL IDENTIFICATION NUMBER (PIN)

The Personal Identification Number (PIN) consists of five digits.

Each digit can be any number from 1-9. There can be no zeros (0) in the PIN. The PIN

must be used to disarm the security system in case the fob becomes unavailable.

HFSM - Entering an Initial PIN:

1 - Select a 5-digit (1 thru 9) initial PIN and record in the Owner's Manual and on the wallet card.

2 - With an assigned fob present, set RUN/OFF switch to OFF.

3 - Turn ignition/headlamp key IGNITION - ON -OFF - ON -OFF - ON.

4 - Press left turn signal button 2 times. Turn signals will flash 3 times.

5 - Press right turn signal button 1 time. Five dashes will appear in the odometer

window. The first dash will flash.

6 - Enter first digit  of initial PIN by pressing left turn signal button a times.

7 - Press right turn signal button 1 time. The digit  will replace the dash in the

odometer. The second dash will flash.

8 - Enter second digit (b) of initial PIN by pressing left turn signal button times.

9 - Press right turn signal button 1 time. The digit will replace the dash in the

odometer. The third dash will flash.

10 - Enter third digit (c) of initial PIN by pressing left turn signal button c times.

11 - Press right turn signal button 1 time. The digit (c) will replace the dash in the

odometer. The fourth dash will flash.

12 - Enter fourth digit (d) of initial PIN by pressing left turn signal button d times.

13 - Press right turn signal button 1 time. The digit (d) will replace the dash in the

odometer. The fifth dash will flash.

14 - Enter fifth digit (e) of initial PIN by pressing left turn signal button e times.

15 - Press right turn signal button 1 time. The digit (e) will replace the dash in the

odometer. The first digit will flash.

16 - Turn the ignition key to OFF.

                                                        HFSM -Changing the PIN 

1 - Select a 5-digit (1 thru 9) personal code and record in the Owner's Manual and on the

wallet card.

2 - With fobs present, turn ignition/headlamp key IGNITION - ON - OFF-ON - OFF -ON.

3 - Press left turn signal button 2 times. Turn signals will flash 3 times.

4 -  Press right turn signal button 1 time. Current PIN will appear in odometer. The first digit will flash.

5 - Enter first digit (a) of new PIN by pressing left turn signal button until desired digit is

displayed in odometer.

6 - Press right turn signal button 1 time. The new digit will replace the current in the odometer. The second digit will flash.

7 - Enter second digit (b) of new PIN by pressing left turn signal button until desired digit

is displayed in odometer.

8 -  Press right turn signal button 1 time. The new digit will replace the current in the odometer. The third digit will flash.

9 - Enter third digit (c) of new PIN by pressing left turn signal button until desired digit is

displayed in odometer.

10 - Press right turn signal button 1 time. The new digit will replace the dash in the

odometer. The fourth digit will flash.

11 - Enter fourth digit (d) of new PIN by pressing left turn signal button until desired digit is

displayed in odometer.

12 -  Press right turn signal button 1 time. The new digit will replace the current in the odometer. The fifth digit will flash.

13 - Enter fifth digit (e) of new PIN by pressing left turn signal button until desired digit is

displayed in odometer.

14 - Press right turn signal button 1 time. The new digit will replace the current in the odometer. The first digit will flash.

15 - Turn the ignition key to OFF. Turning ignition key to OFF stores PIN.

                                                                              HFSM -TRANSPORT MODE

Use this feature when trailering your motorcycle, however, any

attempt to start the engine will trigger the alarm.

To Enter Transport Mode:

1. Turn the Ignition Switch to IGNITION.

2. Set the Engine Stop Switch to OFF.

3. With an assigned fob within range, turn the Ignition Switch

from IGNITION to ACCESS.

4. Simultaneously press both the left and the right turn signal

switches.This must be done within five seconds of turning

the Ignition Switch to ACCESS.

5. After the turn signals flash once, turn the Ignition Switch

to OFF and the module is armed.

6. Confirmation:Turn signal will blink three times when armed

for one ignition cycle.

To Exit Transport Mode:

Return the system to normal operation:

1. With the fob present, turn the Ignition Switch to IGNITION

to disarm the HFSM. To cancel the transport mode, set

the Engine Stop Switch to RUN.

                                                                               TSM/HFSM and ECM Password Learning

1 Install newTSM/HFSM or ECM. Perform all steps under

2 Set engine stop switch to RUN.

3 Turn ignition switch to IGNITION. Verify check engine lamp and security lamp illuminate and then turn off.

    TSM/HFSM enables start relay.

4 Attempt normal start one time. Engine starts and stalls. Check engine lamp illuminates and stays on.

    Password has not been learned. ECM sets DTC P1009.

5 Wait ten seconds. Security lamp illuminates and stays on. ECM enters Password Learning mode for ten minutes.

    Do not cycle ignition switch or interrupt vehicle power or Password Learn will be unsuccessful.  

6 Wait until security lamp turns off.

    This takes ten minutes.

7 Quickly (within one second) turn ignition switch OFFIGNITION.

    ECM must not be allowed to shutdown.

8 Wait until security lamp turns off.

    This takes ten minutes.

9 Quickly (within one second) turn ignition switch OFFIGNITION.

    ECM must not be allowed to shutdown.

10 Wait until security lamp turns off.

    This takes ten minutes.

11 Quickly (within one second) turn ignition switch OFF.

    ECM must not be allowed to shutdown.

12 Turn ignition switch off.

    Wait 15 seconds before turning ignition switch on.

    Turn ignition switch on and start engine to confirm successful Password Learn procedure.

    Clear DTCs.

You will have to take your bike to a HD Stealer to have your HFSM FOB'S programed.